Jenn-Air 36 Induction Cooktop
Jenn-Air 36 Induction Cooktop
Description
The Jenn-Air JIC4536HS brings professional-grade induction cooking to residential kitchens with its expansive 36-inch footprint and five-zone cooking surface. For countertop fabricators, this premium appliance demands precision cutting and expert material handling to ensure flawless installation. This template provides manufacturer-verified dimensions for creating the 33.125" x 19.25" cutout required for proper fitment. Designed for high-end kitchen installations, this induction cooktop serves clients expecting perfection in both performance and aesthetics. Our CNC-ready template eliminates guesswork and reduces installation time while ensuring compliance with manufacturer specifications essential for warranty coverage.
Dimensions
- Overall Width
- 36"
- Overall Depth
- 21"
- Corner Radius
- 0.5"
Specifications
- Manufacturer
- Jenn-Air
- Model Number
- JIC4536HS
- Downloads
- 0
Related Templates
Jenn-Air 30 Induction Cooktop
Jenn-Air
Jenn-Air 30 Downdraft Vent
Jenn-Air
Jenn-Air 36 Downdraft Vent
Jenn-Air
Jenn-Air 30 Electric Cooktop
Jenn-Air
Answer summary
What is the Jenn-Air 36 Induction Cooktop DXF template for?
Jenn-Air 36 Induction Cooktop is a cooktop & range cutouts DXF template for countertop fabrication. Use it only after matching the manufacturer, model, dimensions, variant, and shop workflow to the actual job.
Risk check: Similar-looking products can use different cutout geometry. Confirm the official spec, shop tolerance, material behavior, and CNC output before production.
Next step: Run a DXF check, compare related templates, and keep the current manufacturer spec with the job packet.
Template decision guide
Should you use the Jenn-Air 36 Induction Cooktop DXF template?
Use the template page to shortlist a production file, then verify the exact model, variant, and machine workflow before cutting.
Best fit
Jenn-Air 36 Induction Cooktop is most useful when the product, manufacturer, model, install type, and variant match the job you are fabricating.
What to compare
Compare model number, dimensions, reveal or overhang, bowl or appliance geometry, material thickness, and CNC output requirements.
Risk check
Do not use a similar-looking template as a final production file. Small changes in flange, radius, trim, or reveal can cause a failed cutout.
Evidence to verify
Check the current manufacturer spec, field measurement, template preview, DXF layers, and a shop-approved tolerance before production.
Page-specific notes
Page-specific notes for Jenn-Air 36 Induction Cooktop
These notes are assembled from this exact template record, its category, available variants, and nearby template comparisons. They are meant to make the page more useful than a generic download page.
Exact record SlabWise is using
Jenn-Air JIC4536HS is filed under Cooktop & Range Cutouts. The normalized record lists width 36", depth 21", corner radius 0.5", so the safest use is as a production starting point that still gets checked against the current job packet.
Variant choice
This record is shown as a single template variant. Treat that as a reason to verify reveal, overhang, and cutout assumptions before the file reaches production.
Category-specific production check
Cooktop & Range Cutouts files should be checked for fit against material thickness, edge treatment, sink or appliance clearance, CNC layer expectations, and the shop's preferred tolerance before cutting customer material.
Closest comparisons
Before choosing this file, compare it with Jenn-Air 30 Induction Cooktop, Jenn-Air 30 Downdraft Vent, Jenn-Air 36 Downdraft Vent to catch small model, radius, flange, or layout differences that can change the final cut.
Evidence already attached
This page has extra enrichment for installation overview, CNC cutting notes, material compatibility, buying context. Use those notes as decision support, then keep the official product spec with the job.
The Jenn-Air JIC4536HS brings professional-grade induction cooking to residential kitchens with its expansive 36-inch footprint and five-zone cooking surface. For countertop fabricators, this premium appliance demands precision cutting and expert material handling to ensure flawless installation. This template provides manufacturer-verified dimensions for creating the 33.125" x 19.25" cutout required for proper fitment. Designed for high-end kitchen installations, this induction cooktop serves clients expecting perfection in both performance and aesthetics. Our CNC-ready template eliminates guesswork and reduces installation time while ensuring compliance with manufacturer specifications essential for warranty coverage.
Installation Overview
The JIC4536HS installation requires a precisely cut opening measuring 33.125 inches in width and 19.25 inches in depth, with 0.5-inch corner radii to distribute stress and prevent cracking in stone materials. This 36-inch cooktop provides generous cooking area while fitting standard 36-inch cabinet widths. The unit's 36-inch overall width and 21-inch depth require careful planning in island installations where countertop depth may be limited. Support structures must accommodate the cooktop's weight distribution—approximately 55 pounds—across the cutout perimeter. Fabricators should coordinate with electricians to position the required 240V/50A dedicated circuit appropriately, typically 12-18 inches below the countertop surface and offset from the cutout center to avoid interference. Adequate ventilation clearances include 5-inch minimum to sidewalls and 30-inch minimum to overhead cabinets or vent hoods. The induction technology generates minimal heat transfer to countertops, but control electronics require ventilation beneath the unit.
CNC Cutting Notes
Programming the JIC4536HS cutout demands attention to the 33.125-inch width—this wider span increases deflection risk during cutting, particularly in 3cm materials. Use bridge supports or vacuum pods to prevent material movement. Begin with a 3/8-inch carbide roughing bit for the perimeter cut, maintaining 0.060-inch stock for finishing. Complete the finish pass with a 1/4-inch downcut spiral bit at 70-90 IPM (granite) or 90-110 IPM (quartz), with spindle speeds 18,000-24,000 RPM based on material hardness. The corner radii are non-negotiable—program these as true arcs to prevent stress concentration points. For materials with directional veining, orient the template to minimize vein run-out at corners. This larger cutout generates significant dust; ensure adequate dust collection to maintain bit visibility and cooling. Total cutting time runs 10-15 minutes for 3cm material, longer for exotic granites or ultra-compact surfaces. Post-cutting, inspect all edges with a straightedge to verify the cooktop's mounting clips will engage properly. Any deviation beyond 1/16-inch requires remediation before installation.
Material Compatibility
This template works across all premium countertop materials, though the 33.125-inch width presents unique considerations. In granite, select slabs with minimal fissures or veining parallel to the long axis of the cutout—structural integrity depends on continuous material surrounding the opening. Engineered quartz installations excel with this template due to the material's consistent strength properties; however, verify the slab's warranty covers cutouts this size, as some manufacturers limit coverage for openings exceeding 30 inches. The wider cutout may affect warranty terms with certain quartz brands. Quartzite offers excellent performance but requires premium tooling due to its extreme hardness. For marble installations, this cooktop's minimal heat transfer makes it ideal—unlike gas cooktops, induction won't cause thermal yellowing or calcite breakdown. Porcelain slabs require 12mm minimum thickness and precise cutting due to their brittleness. In islands with waterfall edges, maintain 4-inch minimum material width alongside the cutout to prevent fracture during installation or future impact. Avoid this template in tile, concrete (unless professionally reinforced), or any material under 2cm thickness.
Where to Buy
The Jenn-Air JIC4536HS retails between $2,800-$3,500 depending on finish selection and regional market conditions. Authorized dealers include premium appliance retailers like Abt Electronics, AJ Madison, Designer Appliances, and Yale Appliance, all offering expert consultation and professional delivery services. National chains including Best Buy, Home Depot, and Lowe's stock select models but may require special ordering for specific finishes. Local appliance showrooms often provide superior installation support and direct factory service relationships—valuable for high-end projects. When sourcing for client projects, confirm the exact model suffix (HS, KS, KB) as these indicate different finishes (stainless, black stainless, black) with identical cutout requirements. Professional fabricators benefit from establishing dealer relationships for project pricing and priority delivery scheduling. Online retailers offer competitive pricing but verify shipping methods—cooktops require freight delivery and threshold service. Lead times vary seasonally, from stock availability to 4-6 weeks for special orders. Consider appliance package deals if clients are updating multiple kitchen appliances—dealers often discount bundled purchases.