Jenn-Air 30 Downdraft Vent
Jenn-Air 30 Downdraft Vent
Description
The Jenn-Air JXD7030YS is a premium 30-inch telescoping downdraft ventilation system that rises up to 14 inches from the countertop surface when activated. This CNC-ready template provides the exact cutout dimensions required for professional installation in granite, quartz, marble, and solid surface countertops. With a 600 CFM centrifugal blower and sleek stainless steel design, this downdraft system requires a precise 28.5" x 10.5" countertop opening with 0.25" corner radius to ensure proper fit and optimal performance. Our template is derived directly from Jenn-Air's official dimension guide and includes all critical measurements for flawless fabrication.
Dimensions
- Overall Width
- 30"
- Overall Depth
- 12.125"
- Corner Radius
- 0.25"
Specifications
- Manufacturer
- Jenn-Air
- Model Number
- JXD7030YS
- Downloads
- 0
Related Templates
Jenn-Air 36 Downdraft Vent
Jenn-Air
Jenn-Air 30 Electric Cooktop
Jenn-Air
Jenn-Air 36 Electric Cooktop
Jenn-Air
Jenn-Air 30 Gas Cooktop
Jenn-Air
Answer summary
What is the Jenn-Air 30 Downdraft Vent DXF template for?
Jenn-Air 30 Downdraft Vent is a cooktop & range cutouts DXF template for countertop fabrication. Use it only after matching the manufacturer, model, dimensions, variant, and shop workflow to the actual job.
Risk check: Similar-looking products can use different cutout geometry. Confirm the official spec, shop tolerance, material behavior, and CNC output before production.
Next step: Run a DXF check, compare related templates, and keep the current manufacturer spec with the job packet.
Template decision guide
Should you use the Jenn-Air 30 Downdraft Vent DXF template?
Use the template page to shortlist a production file, then verify the exact model, variant, and machine workflow before cutting.
Best fit
Jenn-Air 30 Downdraft Vent is most useful when the product, manufacturer, model, install type, and variant match the job you are fabricating.
What to compare
Compare model number, dimensions, reveal or overhang, bowl or appliance geometry, material thickness, and CNC output requirements.
Risk check
Do not use a similar-looking template as a final production file. Small changes in flange, radius, trim, or reveal can cause a failed cutout.
Evidence to verify
Check the current manufacturer spec, field measurement, template preview, DXF layers, and a shop-approved tolerance before production.
Page-specific notes
Page-specific notes for Jenn-Air 30 Downdraft Vent
These notes are assembled from this exact template record, its category, available variants, and nearby template comparisons. They are meant to make the page more useful than a generic download page.
Exact record SlabWise is using
Jenn-Air JXD7030YS is filed under Cooktop & Range Cutouts. The normalized record lists width 30", depth 12.125", corner radius 0.25", so the safest use is as a production starting point that still gets checked against the current job packet.
Variant choice
This record is shown as a single template variant. Treat that as a reason to verify reveal, overhang, and cutout assumptions before the file reaches production.
Category-specific production check
Cooktop & Range Cutouts files should be checked for fit against material thickness, edge treatment, sink or appliance clearance, CNC layer expectations, and the shop's preferred tolerance before cutting customer material.
Closest comparisons
Before choosing this file, compare it with Jenn-Air 36 Downdraft Vent, Jenn-Air 30 Electric Cooktop, Jenn-Air 36 Electric Cooktop to catch small model, radius, flange, or layout differences that can change the final cut.
Evidence already attached
This page has extra enrichment for installation overview, CNC cutting notes, material compatibility, buying context. Use those notes as decision support, then keep the official product spec with the job.
The Jenn-Air JXD7030YS is a premium 30-inch telescoping downdraft ventilation system that rises up to 14 inches from the countertop surface when activated. This CNC-ready template provides the exact cutout dimensions required for professional installation in granite, quartz, marble, and solid surface countertops. With a 600 CFM centrifugal blower and sleek stainless steel design, this downdraft system requires a precise 28.5" x 10.5" countertop opening with 0.25" corner radius to ensure proper fit and optimal performance. Our template is derived directly from Jenn-Air's official dimension guide and includes all critical measurements for flawless fabrication.
Installation Overview
Installing the Jenn-Air JXD7030YS downdraft requires careful planning and precise countertop fabrication. The primary cutout measures 28.5 inches wide by 10.5 inches deep with rounded corners featuring a 0.25-inch radius. The unit's overall footprint is 30 inches wide by 12.125 inches deep, requiring adequate cabinet space below for the motor housing and ductwork. The reversible motor box allows for flexible installation with the blower positioned on either side of the unit. Fabricators should ensure the countertop material is at least 1.25 inches thick for structural integrity around the cutout perimeter. The downdraft extends 14 inches above the countertop when fully raised, so verify adequate clearance if installing below overhead cabinets or shelving. Electrical requirements include a dedicated 120V, 15-amp circuit positioned within the cabinet base. For ventilation, the system accommodates either a 3.25" x 10" rectangular duct or 6" round duct, which can be routed through the floor or rear wall depending on kitchen layout.
CNC Cutting Notes
When programming your CNC for this downdraft cutout, precision is critical to ensure the unit seats properly and operates smoothly. Start by importing the DXF template and verifying all dimensions match the specified 28.5" x 10.5" opening. Use a 0.25-inch radius end mill or ball nose bit for the corner radii to match the manufacturer specifications exactly. For granite and quartzite, we recommend a cutting speed of 60-80 inches per minute with adequate water flow to prevent heat buildup and material stress. Quartz and engineered stone can typically handle slightly faster speeds at 80-100 IPM. Begin with an outside profile cut, maintaining a 0.010-inch tolerance for a snug fit without binding. Pay special attention to corner quality, as chips or irregularities can interfere with the mounting brackets. For brittle materials like marble, reduce feed rates by 20-30% and ensure proper support beneath the cutout area to prevent cracking as the center section releases. After cutting, perform a thorough edge inspection and use hand polishing to smooth any minor imperfections. Test-fit the unit before final installation to verify proper clearance and alignment with cabinet structure below.
Material Compatibility
This downdraft cutout template is compatible with all standard countertop materials used in residential and commercial applications. Granite and natural stone installations require standard diamond tooling with wet cutting to prevent thermal shock and edge chipping. The 28.5-inch width provides sufficient edge support even with full-height backsplashes. Quartz and engineered stone materials are ideal candidates, as they offer excellent structural stability around the cutout perimeter and resist heat from cooking activities. Solid surface materials like Corian require special attention to heat resistance, so verify the specific product's temperature rating exceeds 350°F for downdraft installations. Laminate countertops are generally not recommended for downdraft ventilation due to heat sensitivity and structural concerns, though high-pressure laminate with marine-grade substrate may be acceptable in budget applications. Concrete countertops work well but require additional structural reinforcement around the cutout and waterproof sealing to prevent moisture infiltration. Stainless steel and metal countertops are fully compatible and often used in professional kitchen settings. Butcher block and wood surfaces should be avoided in the immediate downdraft area due to heat and moisture concerns. For seam placement, avoid positioning seams within 6 inches of the cutout perimeter to maintain structural integrity.
Where to Buy
The Jenn-Air JXD7030YS downdraft ventilation system is available through multiple authorized dealers and retailers nationwide. For online purchasing, visit the official Jenn-Air website at jennair.com where you can browse the full downdraft collection and use their dealer locator to find certified installers in your area. Major appliance retailers including Designer Appliances, US Appliance, and AJ Madison stock this model and offer competitive pricing with delivery options. For in-person shopping, authorized Jenn-Air dealers provide showroom displays where you can see the unit's telescoping action and discuss installation requirements with trained staff. Regional dealers such as Metropolitan Appliance (Seattle), Wilson AC & Appliance (Austin), DeWhitt Appliance (Portland), and Mrs. G TV & Appliances (New Jersey) maintain inventory and offer local installation services. Home improvement chains occasionally stock Jenn-Air downdraft systems, though selection may be limited compared to specialty appliance retailers. For the best pricing, compare quotes from multiple dealers and watch for seasonal promotions, typically offered during spring kitchen remodeling season and fall holiday sales events. Professional installers and kitchen designers can often secure contractor pricing through their dealer relationships. When purchasing, verify that the unit includes all mounting hardware, installation instructions, and warranty registration materials.