Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout
Description
The Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout template delivers precision DXF geometry for professional stone fabrication. With dimensions of standard dimensions, this template provides CNC-ready profiles that ensure consistent, repeatable results. Designed for the sinks category, this template streamlines the fabrication process from initial programming through final finishing. Professional shops rely on accurate templates like this to minimize waste and maximize production efficiency across installations.
Dimensions
- Overall Width
- 32"
- Overall Depth
- 18"
- Bowl Width
- 30"
- Bowl Depth
- 16"
- Corner Radius
- 0.375"
Specifications
- Manufacturer
- Nantucket Sinks
- Model Number
- ZR3218-16
- Installation Type
- Undermount
- Bowl Configuration
- Single
- Material
- Stainless-Steel
- Min. Cabinet Width
- 36"
- Downloads
- 0
Related Templates
Nantucket Sinks ?FCF-2418-FS Cape 24 Fireclay Farmhouse 24" Single Bowl Farmhouse Sink Cutout
Nantucket Sinks
Nantucket Sinks ?FCF-3020-FS Cape 30 Fireclay Farmhouse 30" Single Bowl Farmhouse Sink Cutout
Nantucket Sinks
Nantucket Sinks ?FCF-3318D-FS Cape 33 Fireclay Farmhouse Double 33" Double Equal Bowl Farmhouse Sink Cutout
Nantucket Sinks
Nantucket Sinks NS09i-16 Rectangle 9 Undermount Bar 17" Single Bowl Undermount Sink Cutout
Nantucket Sinks
The Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout template delivers precision DXF geometry for professional stone fabrication. With dimensions of standard dimensions, this template provides CNC-ready profiles that ensure consistent, repeatable results. Designed for the sinks category, this template streamlines the fabrication process from initial programming through final finishing. Professional shops rely on accurate templates like this to minimize waste and maximize production efficiency across installations.
Installation Overview
The fabrication process for the Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
CNC programming for the Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout should account for tool wear compensation, especially on abrasive marble stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The nantucket geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Nantucket Sinks ZR3218-16 Pro Series 32x18 Undermount 32" Single Bowl Undermount Sink Cutout template works exceptionally well with natural granite, providing clean edges that polish to a high gloss. Marble is also compatible, though the softer stone requires reduced feed rates during CNC operations to prevent micro-chipping. Quartzite offers excellent results with this profile, as the hard mineral structure holds fine details well. Engineered quartz composites are ideal substrates, offering consistent material properties that produce predictable results. Soapstone and slate can be profiled using this template with appropriate tooling adjustments. For limestone, use conservative CNC parameters due to the stone's tendency to chip on detailed profiles. Porcelain sintered stone panels require specialized diamond tooling but produce excellent results with the nantucket geometry.
Where to Buy
Professional fabricators can source marble slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.