Franke MAG61031 Maris 31 Granite Single Sink Cutout
Franke MAG61031 Maris 31 Granite Single Sink Cutout
Description
The Franke MAG61031 Maris 31 Granite Single Sink Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Dimensions
- Overall Width
- 33"
- Overall Depth
- 22"
- Bowl Width
- 31.5"
- Bowl Depth
- 16.6875"
- Corner Radius
- 0.75"
Specifications
- Manufacturer
- Franke
- Model Number
- MAG61031
- Installation Type
- Undermount
- Bowl Configuration
- Single
- Material
- Granite-Composite
- Min. Cabinet Width
- 33"
- Downloads
- 0
Related Templates
Franke CLV110-28 Crysta Undermount Sink- CLV110-28 Stainless steel Kitchen Cutout
Franke
Franke CUX110-30 Cube 32 Single Sink Cutout
Franke
Franke CUX11010 Culinary Center Sink - CUX11010-W Stainless steel Kitchen Cutout
Franke
Franke CUX11015 Cube Undermount Sink - CUX11015 Stainless steel Kitchen Cutout
Franke
Answer summary
What is the Franke MAG61031 Maris 31 Granite Single Sink Cutout DXF template for?
Franke MAG61031 Maris 31 Granite Single Sink Cutout is a sink cutouts DXF template for countertop fabrication. Use it only after matching the manufacturer, model, dimensions, variant, and shop workflow to the actual job.
Risk check: Similar-looking products can use different cutout geometry. Confirm the official spec, shop tolerance, material behavior, and CNC output before production.
Next step: Run a DXF check, compare related templates, and keep the current manufacturer spec with the job packet.
Template decision guide
Should you use the Franke MAG61031 Maris 31 Granite Single Sink Cutout DXF template?
Use the template page to shortlist a production file, then verify the exact model, variant, and machine workflow before cutting.
Best fit
Franke MAG61031 Maris 31 Granite Single Sink Cutout is most useful when the product, manufacturer, model, install type, and variant match the job you are fabricating.
What to compare
Compare model number, dimensions, reveal or overhang, bowl or appliance geometry, material thickness, and CNC output requirements.
Risk check
Do not use a similar-looking template as a final production file. Small changes in flange, radius, trim, or reveal can cause a failed cutout.
Evidence to verify
Check the current manufacturer spec, field measurement, template preview, DXF layers, and a shop-approved tolerance before production.
Page-specific notes
Page-specific notes for Franke MAG61031 Maris 31 Granite Single Sink Cutout
These notes are assembled from this exact template record, its category, available variants, and nearby template comparisons. They are meant to make the page more useful than a generic download page.
Exact record SlabWise is using
Franke MAG61031 is filed under Sink Cutouts. The normalized record lists width 33", depth 22", bowl width 31.5", bowl depth 16.6875", corner radius 0.75", so the safest use is as a production starting point that still gets checked against the current job packet.
Variant choice
This page exposes 4 variants: No Reveal (Flush), 1/8" Reveal, 1/2" Overhang, Drop-in. Pick the variant that matches reveal, overhang, install style, and shop standard before exporting to CAM.
Category-specific production check
Sink Cutouts files should be checked for fit against material thickness, edge treatment, sink or appliance clearance, CNC layer expectations, and the shop's preferred tolerance before cutting customer material.
Closest comparisons
Before choosing this file, compare it with Franke CLV110-28 Crysta Undermount Sink- CLV110-28 Stainless steel Kitchen Cutout, Franke CUX110-30 Cube 32 Single Sink Cutout, Franke CUX11010 Culinary Center Sink - CUX11010-W Stainless steel Kitchen Cutout to catch small model, radius, flange, or layout differences that can change the final cut.
Evidence already attached
This page has extra enrichment for installation overview, CNC cutting notes, material compatibility, buying context. Use those notes as decision support, then keep the official product spec with the job.
The Franke MAG61031 Maris 31 Granite Single Sink Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Installation Overview
Installing the Franke MAG61031 Maris 31 Granite Single Sink Cutout template requires standard stone fabrication procedures adapted for the sinks category. Begin with accurate field measurements to verify the template dimensions match the installation site. Import the DXF file into CNC programming software and create an optimized cutting plan that minimizes material waste. For the cutting phase, select appropriate diamond tooling based on the stone type being fabricated. Maintain consistent coolant flow during all CNC operations to prevent thermal damage. After cutting, perform edge finishing according to the template specifications. Dry-fit all pieces at the installation site before applying adhesive. Use construction-grade silicone or epoxy appropriate for stone installations. Ensure proper support for all sections, adding brackets where overhangs exceed manufacturer recommendations. Apply a penetrating sealer after installation to protect the finished surface. Final inspection should verify all dimensions match the template within acceptable tolerances.
CNC Cutting Notes
CNC programming for the Franke MAG61031 Maris 31 Granite Single Sink Cutout should account for tool wear compensation, especially on abrasive dolomite stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The franke geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Franke MAG61031 Maris 31 Granite Single Sink Cutout profile pairs best with medium-to-hard natural stones and engineered materials. Granite is the ideal substrate, offering the hardness needed to maintain the franke geometry while accepting a brilliant polish. Quartz composites provide consistent results with minimal tool wear variation. For softer stones like marble or limestone, the profile remains achievable but requires adjusted CNC parameters and additional care during finishing. Exotic stones such as quartzite and super-white dolomite produce stunning results with this profile. Sintered stone panels are compatible when using specialized thin-material tooling. Always perform a test cut on representative material before beginning production runs.
Where to Buy
Professional fabricators can source dolomite slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.