Delta 95D932-33S Rivet 33 Drop-In Single Sink Cutout
Description
Production-ready DXF cutout template for the Delta 95D932-33S Rivet 33 Drop-In Single 33" x 22" single bowl drop-in sink. Available in 4 variants: no reveal, 1/8" reveal, 1/2" overhang, and drop-in.
Dimensions
- Overall Width
- 33"
- Overall Depth
- 22"
- Bowl Width
- 30.5"
- Bowl Depth
- 18"
- Corner Radius
- 0.375"
Specifications
- Manufacturer
- Delta
- Model Number
- 95D932-33S
- Installation Type
- Drop-In
- Bowl Configuration
- Single
- Material
- Stainless-Steel
- Min. Cabinet Width
- 36"
- Downloads
- 0
Related Templates
Delta 26B903-25S Lenta 25 Single Sink Cutout
Delta
Delta 26B903-33S Lenta 33 Single Drop-In Sink Cutout
Delta
Delta 75D932-33S Lorelei 33 Granite Workstation Sink Cutout
Delta
Delta 95A935-25S Rivet 25 Drop-In Sink Cutout
Delta
The Delta 95D932-33S Rivet 33 Drop-In Single Sink Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Installation Overview
The fabrication process for the Delta 95D932-33S Rivet 33 Drop-In Single Sink Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
CNC programming for the Delta 95D932-33S Rivet 33 Drop-In Single Sink Cutout should account for tool wear compensation, especially on abrasive engineered quartz stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The delta geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Delta 95D932-33S Rivet 33 Drop-In Single Sink Cutout profile pairs best with medium-to-hard natural stones and engineered materials. Granite is the ideal substrate, offering the hardness needed to maintain the delta geometry while accepting a brilliant polish. Quartz composites provide consistent results with minimal tool wear variation. For softer stones like marble or limestone, the profile remains achievable but requires adjusted CNC parameters and additional care during finishing. Exotic stones such as quartzite and super-white dolomite produce stunning results with this profile. Sintered stone panels are compatible when using specialized thin-material tooling. Always perform a test cut on representative material before beginning production runs.
Where to Buy
Professional fabricators can source engineered quartz slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.