Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout
Description
The Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout template delivers precision DXF geometry for professional stone fabrication. With dimensions of standard dimensions, this template provides CNC-ready profiles that ensure consistent, repeatable results. Designed for the sinks category, this template streamlines the fabrication process from initial programming through final finishing. Professional shops rely on accurate templates like this to minimize waste and maximize production efficiency across installations.
Dimensions
- Overall Width
- 20"
- Overall Depth
- 14"
- Bowl Width
- 18"
- Bowl Depth
- 12"
Specifications
- Manufacturer
- Ruvati
- Model Number
- RVH6211ST
- Installation Type
- Undermount
- Bowl Configuration
- Single
- Material
- Stainless-Steel
- Min. Cabinet Width
- 24"
- Downloads
- 0
Related Templates
Ruvati RVG1033 Valencia 33x22 Granite Double 33" Double Equal Bowl Undermount Sink Cutout
Ruvati
Ruvati RVG1080 Valencia 33x22 Granite Single 33" Single Bowl Undermount Sink Cutout
Ruvati
Ruvati RVG2030 Valencia 30x18 Granite Composite 30" Single Bowl Undermount Sink Cutout
Ruvati
Ruvati RVG2033 Valencia 33x22 Granite Undermount 33" Single Bowl Undermount Sink Cutout
Ruvati
The Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout template delivers precision DXF geometry for professional stone fabrication. With dimensions of standard dimensions, this template provides CNC-ready profiles that ensure consistent, repeatable results. Designed for the sinks category, this template streamlines the fabrication process from initial programming through final finishing. Professional shops rely on accurate templates like this to minimize waste and maximize production efficiency across installations.
Installation Overview
The fabrication process for the Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
CNC programming for the Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout should account for tool wear compensation, especially on abrasive marble stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The ruvati geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Ruvati RVH6211ST 20 X 14 Inch Brushed Stainless Steel Rectangular Bathroom Sink Semi Recessed Cutout template works exceptionally well with natural granite, providing clean edges that polish to a high gloss. Marble is also compatible, though the softer stone requires reduced feed rates during CNC operations to prevent micro-chipping. Quartzite offers excellent results with this profile, as the hard mineral structure holds fine details well. Engineered quartz composites are ideal substrates, offering consistent material properties that produce predictable results. Soapstone and slate can be profiled using this template with appropriate tooling adjustments. For limestone, use conservative CNC parameters due to the stone's tendency to chip on detailed profiles. Porcelain sintered stone panels require specialized diamond tooling but produce excellent results with the ruvati geometry.
Where to Buy
Professional fabricators can source marble slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.