Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout
Description
The Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Dimensions
- Overall Width
- 31.91"
- Overall Depth
- 20.66"
- Bowl Width
- 29.9062"
- Bowl Depth
- 18.6599"
- Corner Radius
- 90.8199"
Specifications
- Manufacturer
- Karran
- Model Number
- E-360R
- Installation Type
- Undermount
- Bowl Configuration
- Offset-Double
- Material
- Stainless-Steel
- Min. Cabinet Width
- 34"
- Downloads
- 0
Related Templates
Karran A-360R Acrylic Offset Double Bowl Undermount Cutout
Karran
Karran E-560L Stainless Steel Offset Double Bowl Undermount Cutout
Karran
Karran E-560R Stainless Steel Offset Double Bowl Undermount Cutout
Karran
Karran EL-78L Stainless Steel Offset Double Bowl Undermount Cutout
Karran
The Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Installation Overview
The fabrication process for the Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
For the Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout profile, set your CNC router spindle speed between 5000-7000 RPM for dolomite substrates. Use a feed rate of 40-60 IPM for roughing passes and reduce to 20-30 IPM for finishing passes. Select a diamond-tipped profile bit matching the template radius specifications. Program the toolpath using climb milling for cleaner cuts on the karran geometry. Maintain coolant flow at 2+ GPM to prevent thermal fracturing. For harder stones like granite, reduce feed rates by 20% and increase water flow. Run a test cut on scrap material to verify the profile matches the DXF template before committing to production stock.
Material Compatibility
The Karran E-360R Stainless Steel Offset Double Bowl Undermount Cutout profile pairs best with medium-to-hard natural stones and engineered materials. Granite is the ideal substrate, offering the hardness needed to maintain the karran geometry while accepting a brilliant polish. Quartz composites provide consistent results with minimal tool wear variation. For softer stones like marble or limestone, the profile remains achievable but requires adjusted CNC parameters and additional care during finishing. Exotic stones such as quartzite and super-white dolomite produce stunning results with this profile. Sintered stone panels are compatible when using specialized thin-material tooling. Always perform a test cut on representative material before beginning production runs.
Where to Buy
Professional fabricators can source dolomite slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.