Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout
Description
The Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Dimensions
- Overall Width
- 36"
- Overall Depth
- 25"
- Bowl Width
- 34"
- Bowl Depth
- 23"
- Corner Radius
- 0.5"
Specifications
- Manufacturer
- Just Manufacturing
- Model Number
- ?SL-3625
- Installation Type
- Undermount
- Bowl Configuration
- Single
- Material
- Stainless-Steel
- Min. Cabinet Width
- 39"
- Downloads
- 0
Related Templates
Just Manufacturing ?CUF-1815 Commercial 18x15 18" Single Bowl Undermount Sink Cutout
Just Manufacturing
Just Manufacturing ?CUF-2418 Commercial 24x18 24" Single Bowl Undermount Sink Cutout
Just Manufacturing
Just Manufacturing ?CUF-3018 Commercial 30x18 30" Single Bowl Undermount Sink Cutout
Just Manufacturing
Just Manufacturing ?DI-2522 Drop-In Single 25x22 25" Single Bowl Drop In Sink Cutout
Just Manufacturing
The Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout is a production-ready DXF template engineered for sinks fabrication projects. At standard dimensions, this template addresses the specific requirements of professional stone fabrication with accurate CNC-ready geometry. Fabricators benefit from standardized dimensions that reduce setup time and improve consistency. This template represents proven configurations used daily in professional fabrication shops.
Installation Overview
Installing the Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout template requires standard stone fabrication procedures adapted for the sinks category. Begin with accurate field measurements to verify the template dimensions match the installation site. Import the DXF file into CNC programming software and create an optimized cutting plan that minimizes material waste. For the cutting phase, select appropriate diamond tooling based on the stone type being fabricated. Maintain consistent coolant flow during all CNC operations to prevent thermal damage. After cutting, perform edge finishing according to the template specifications. Dry-fit all pieces at the installation site before applying adhesive. Use construction-grade silicone or epoxy appropriate for stone installations. Ensure proper support for all sections, adding brackets where overhangs exceed manufacturer recommendations. Apply a penetrating sealer after installation to protect the finished surface. Final inspection should verify all dimensions match the template within acceptable tolerances.
CNC Cutting Notes
CNC programming for the Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout should account for tool wear compensation, especially on abrasive engineered quartz stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The just geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Just Manufacturing ?SL-3625 Single Bowl 36x25 36" Single Bowl Undermount Sink Cutout profile pairs best with medium-to-hard natural stones and engineered materials. Granite is the ideal substrate, offering the hardness needed to maintain the just geometry while accepting a brilliant polish. Quartz composites provide consistent results with minimal tool wear variation. For softer stones like marble or limestone, the profile remains achievable but requires adjusted CNC parameters and additional care during finishing. Exotic stones such as quartzite and super-white dolomite produce stunning results with this profile. Sintered stone panels are compatible when using specialized thin-material tooling. Always perform a test cut on representative material before beginning production runs.
Where to Buy
Professional fabricators can source engineered quartz slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.