Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout
Description
Professional fabricators turn to the Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout template for accurate sinks production work. The standard dimensions specifications provide the exact geometry needed for CNC-based fabrication workflows. This DXF template eliminates manual layout work while ensuring every piece meets the tight tolerances required for quality installations. The design works well across multiple stone types and installation scenarios.
Dimensions
- Overall Width
- 36"
- Overall Depth
- 19.875"
- Bowl Width
- 33.25"
- Bowl Depth
- 16.875"
- Corner Radius
- 0.25"
Specifications
- Manufacturer
- Franke
- Model Number
- MHK720-35
- Installation Type
- Farmhouse
- Bowl Configuration
- Double
- Material
- Fireclay
- Min. Cabinet Width
- 36"
- Downloads
- 0
Related Templates
Franke FH2K710-33S Farm House 33 Fireclay Sink Cutout
Franke
Franke MHK110-24 Manor House 24 Fireclay Sink Cutout
Franke
Franke MHK110-28 Manor House 28 Fireclay Sink Cutout
Franke
Franke MHK110-33 Manor House 33 Fireclay Sink Cutout
Franke
Professional fabricators turn to the Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout template for accurate sinks production work. The standard dimensions specifications provide the exact geometry needed for CNC-based fabrication workflows. This DXF template eliminates manual layout work while ensuring every piece meets the tight tolerances required for quality installations. The design works well across multiple stone types and installation scenarios.
Installation Overview
The fabrication process for the Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
CNC programming for the Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout should account for tool wear compensation, especially on abrasive natural stone stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The franke geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
The Franke MHK720-35 Manor House 36 Double Fireclay Sink Cutout profile pairs best with medium-to-hard natural stones and engineered materials. Granite is the ideal substrate, offering the hardness needed to maintain the franke geometry while accepting a brilliant polish. Quartz composites provide consistent results with minimal tool wear variation. For softer stones like marble or limestone, the profile remains achievable but requires adjusted CNC parameters and additional care during finishing. Exotic stones such as quartzite and super-white dolomite produce stunning results with this profile. Sintered stone panels are compatible when using specialized thin-material tooling. Always perform a test cut on representative material before beginning production runs.
Where to Buy
Professional fabricators can source natural stone slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.