E2 Stainless ECLIPSE D801 Undermount Stainless Steel Cutout
Description
Production-ready DXF cutout template for the E2 Stainless ECLIPSE D801 Undermount Stainless Steel 33.03" x 21.18" single bowl undermount sink. Available in 4 variants: no reveal, 1/8" reveal, 1/2" overhang, and drop-in.
Dimensions
- Overall Width
- 33.03"
- Overall Depth
- 21.18"
- Bowl Width
- 31.0336"
- Bowl Depth
- 19.1833"
Specifications
- Manufacturer
- E2 Stainless
- Model Number
- ECLIPSE D801
- Installation Type
- Undermount
- Bowl Configuration
- Single
- Material
- Stainless-Steel
- Min. Cabinet Width
- 35"
- Downloads
- 0
Related Templates
E2 Stainless ECLIPSE 183 Undermount Stainless Steel Cutout
E2 Stainless
E2 Stainless ECLIPSE 193 Undermount Stainless Steel Cutout
E2 Stainless
E2 Stainless ECLIPSE 194 Undermount Stainless Steel Cutout
E2 Stainless
E2 Stainless ECLIPSE 301 Undermount Stainless Steel Cutout
E2 Stainless
The E2 Stainless ECLIPSE D801 Undermount Stainless Steel Cutout template delivers precision DXF geometry for professional stone fabrication. With dimensions of standard dimensions, this template provides CNC-ready profiles that ensure consistent, repeatable results. Designed for the sinks category, this template streamlines the fabrication process from initial programming through final finishing. Professional shops rely on accurate templates like this to minimize waste and maximize production efficiency across installations.
Installation Overview
The fabrication process for the E2 Stainless ECLIPSE D801 Undermount Stainless Steel Cutout begins with DXF template verification and material selection. Import the template geometry into your CAM software, setting appropriate tool paths for the sinks specifications. Select diamond tooling rated for the specific stone material being processed. CNC cutting should proceed in stages: roughing passes followed by finishing passes at full depth. Maintain proper coolant flow throughout all machining operations. After all pieces are cut, perform any required edge finishing or polishing operations. Transport pieces to the installation site using appropriate lifting equipment and A-frame racks. On-site, verify cabinet or substrate preparation meets installation requirements. Apply adhesive in the recommended pattern and set pieces beginning with the largest section. Complete all joints with color-matched epoxy. Allow full cure time before loading the installation with fixtures or appliances. Seal all exposed surfaces with an appropriate stone sealer.
CNC Cutting Notes
CNC programming for the E2 Stainless ECLIPSE D801 Undermount Stainless Steel Cutout should account for tool wear compensation, especially on abrasive granite stones. Recommended parameters: spindle speed 4500-6500 RPM, feed rate 35-55 IPM for roughing. The e2 geometry benefits from a two-pass strategy — rough to within 2mm of final profile, then finish at reduced feed rate (15-25 IPM). Use plunge rates no faster than 10 IPM to prevent tool breakage. Monitor vibration levels during cutting; excessive chatter indicates tool wear or incorrect speed/feed settings. Keep backup tooling on hand for production runs exceeding 50 linear feet of edge profile.
Material Compatibility
This e2 profile is compatible with a wide range of countertop materials. Natural granite remains the most popular substrate, offering durability and an attractive polished finish. Engineered quartz performs excellently, with consistent material properties that make CNC cutting predictable and efficient. Marble requires more careful handling — reduce feed rates by 15-20% to prevent veining from causing unpredictable fractures. Quartzite is an excellent choice for this profile, as the material's hardness preserves fine geometric details through years of use. Dolomite and travertine can be profiled with adjusted parameters. Avoid ultra-thin porcelain slabs for complex profiles without proper backing support.
Where to Buy
Professional fabricators can source granite slabs from local stone distributors and wholesale suppliers. Visit SlabWise for template downloads and fabrication resources.