Description
This universal eased/straight edge template serves as the baseline profile for all 2cm+2cm laminated countertop fabrication, providing standard CNC parameters suitable for a broad range of stone and engineered surface materials. At 1-9/16 inches total thickness, the laminated build-up creates a visually substantial countertop edge from two thinner slabs. The template specifies a 25mm roughing finger bit at 3500 RPM and a comprehensive polishing sequence from 50 grit through 3000 grit plus buff, running up to 4000 RPM. When working with a material that does not have its own dedicated template variant, this general-purpose profile provides reliable starting parameters that fabricators can fine-tune based on their specific stone and equipment. The eased top corner detail is the industry standard for residential countertops, offering a clean look with minimal chip risk.
Related Templates
Eased/Straight Edge Profile (Granite) - 2cm+2cm Laminated
Eased/Straight Edge Profile (Marble) - 2cm+2cm Laminated
Eased/Straight Edge Profile (Porcelain) - 2cm+2cm Laminated
Eased/Straight Edge Profile (Quartz (Engineered)) - 2cm+2cm Laminated
This universal eased/straight edge template serves as the baseline profile for all 2cm+2cm laminated countertop fabrication, providing standard CNC parameters suitable for a broad range of stone and engineered surface materials. At 1-9/16 inches total thickness, the laminated build-up creates a visually substantial countertop edge from two thinner slabs. The template specifies a 25mm roughing finger bit at 3500 RPM and a comprehensive polishing sequence from 50 grit through 3000 grit plus buff, running up to 4000 RPM. When working with a material that does not have its own dedicated template variant, this general-purpose profile provides reliable starting parameters that fabricators can fine-tune based on their specific stone and equipment. The eased top corner detail is the industry standard for residential countertops, offering a clean look with minimal chip risk.
Installation Overview
The universal laminated eased/straight template applies to any material combination where two 2cm slabs are bonded together for edge buildup. Begin by selecting an adhesive appropriate for the specific substrate, as bonding requirements vary significantly between natural stone, engineered quartz, porcelain, and ultracompact materials. Clean both bonding surfaces thoroughly and ensure they are flat and free of debris. Apply adhesive evenly across the full bonding area and clamp with consistent pressure. Cure times depend on the adhesive type and shop temperature, so follow the manufacturer's specifications. After the lamination has fully cured, secure the workpiece on the CNC table and verify that the combined thickness measures approximately 1.575 inches at the edge location. Run the roughing pass with the 25mm finger bit at 3500 RPM, feeding at 40-70 IPM depending on material hardness. The seam polishing pass at 2500 RPM addresses the visible lamination joint before proceeding through the main polishing sequence. Progress from 50 grit metal bond at 2800 RPM through eight additional positions to the buff pad at 4000 RPM. Adjust feed rates and water flow based on how the specific material responds during the first few inches of cutting. This template provides reliable baseline settings, but the best results come from calibrating to your particular combination of stone, tooling brand, and CNC machine characteristics.
CNC Cutting Notes
This universal template provides mid-range CNC parameters suitable as a starting point for most materials. Set roughing at 3500 RPM with feed rates between 40-70 IPM depending on material hardness. Harder stones like granite and quartzite perform better at the lower end of that range, while softer materials can tolerate higher feed speeds. Depth of cut should be 0.040-0.060 inches per pass. The polishing sequence runs from 50 grit at 2800 RPM to buff at 4000 RPM across nine positions. Run test sections on offcut material before committing to the full edge run, especially when working with an unfamiliar stone. Monitor for chipping, burning, or incomplete scratch removal as indicators that speeds or feeds need adjustment.
Material Compatibility
This general-purpose template is designed to work across the full spectrum of countertop materials including granite, marble, engineered quartz, porcelain, quartzite, and ultracompact surfaces. However, for optimal results on any specific material, consider using the material-specific variant of this template if available. Marble benefits from lower RPMs to prevent thermal damage, while quartzite and ultracompact surfaces typically require higher speeds than these baseline settings provide. This universal template is ideal for mixed-material shops that process a variety of stone types and need a reliable default profile loaded in their CNC controller.
Where to Buy
Countertop slabs in all material types are available from national distributors such as MSI, Arizona Tile, Daltile, and Cosentino, as well as independent regional stone yards. For lamination adhesives, contact Integra Adhesives, Akemi, or Tenax for products matched to your specific substrate.